The most trusted car stereo shop in San Diego

The most trusted car stereo shop in San Diego

At this point, buying preamps and discrete seperate audio components may well be getting you in too deep. There’s a lot of knowledge you need to have before you try to do anything in that route. Especially since you’re talking about 4-ohm speakers. Almost all consumer-level equipment is 8-ohm If you use different impedance equipment say 4ohm speakers with a receiver rated for 8ohms without taking into consideration all the factors, you can easily damage or destroy your speakers and the amplifier section of your receiver or discrete amplifier, etc etc It is possible to run mismatched equipment but speakers have to be hooked up in groups bye bye 5. There is such a thing as a bridgeable amplifier, but no, you can’t hook two high-ohm receivers together to run a low-ohm speaker. As for how much power you need, watts per channel is more than enough for most people’s home theatre. Go much above that and you’ll be getting the cops called on you for noise complaints. You were asking me about running this system for listening to mp3s and downloaded movies off your computer. To be brutally honest, you’re going way overkill. The Yamaha RX series receivers you were looking at were perfect for what you’re wanting to do.

Hook up an iPhone, or iPod, to your car

If you have speakers already connected to your stereo, fully disconnect them. Active crossover units are larger than passive ones and need to be mounted in a stable location, ideally near your amplifiers. Using the appropriate cables, wire your crossover into the receiver or preamp, with the wires coming out of the receiver going into the “in” terminals on the crossover. Depending on your receiver and your stereo system, you will probably be making this connection with RCA cables, but some crossovers will are set up to use speaker wire instead as detailed in Method 1 if your receiver doesn’t have RCA outputs.

Using the appropriate cables again, usually RCA or speaker wire for a home stereo system , connect the appropriate outputs to the appropriate amplifiers. If you don’t have a subwoofer, you’ll send your high frequency signal to your tweeter amp and low-frequency signal to your woofer amp.

Hooking up a 4 channel amp to your front and rear speakers takes some work and time, but it’s a great way to get sound you’ll love. Considering buying an amplifier? You can find some great 4 channel amps (including the Alpine MRV-F pictured here) in my 4 channel amp buyer’s guide.

How do you hook up a new car stereo? Well it helps if you have a repair manual for your car so that you can reference the wiring schematic for the stereo connections it will eliminate a lot of guess work. Using a multimeter find a wire in the connector in the dash that was formerly on the stock radio that has 12 vol…ts when the key is off and this will be your Batt. Now with the key on find a second wire with 12 volts and this will be your Ign.

If you have a power antenna there should be a connection for that on the new stereo and the wiring schematic will tell you which one that is. As for the speakers once again a schematic is the best way but you can take fir instance the left front speaker wires from the new stereo with the unit turned on and tuned to a station and through trial and error find the two that feed the left front speaker or Ive heard you can use a 9v battery and listen for a buzz to identify the correct wires, or use the continuity tester on the multimeter to identify the wires.

If you have all your music on a portable MP3 player, such as an Apple iPod, there’s an easy way to listen to it through the big speakers on your home-stereo system. You can choose between three options: Connecting …the iPod via headphone jack All you need is a simple Y cable, which is available from any home-electronics store. Connect the small plug to the headphone output of your iPod–or any portable audio player. Then connect the red and white RCA-style plugs to the matching inputs on the back of your stereo receiver or boombox.

Connecting the iPod via iPod dock To connect using the iPod dock, you first need to purchase an iPod dock accessory. Using the same type of Y cable, connect the small plug to the matching jack on the rear of the iPod dock.

6 Best 6×9 Car Speakers to Buy in 2018

LOADS Amplifiers are designed to power a specific “load”, meaning a speaker or set of speakers having a specific “AC impedance” measured in ohms. Impedance resists the flow of electric current so the higher the speaker impedance the less current the amplifier has to supply. Conversely, the lower the impedance the more current must be supplied. In other words, a low impedance speaker is a big workload for your amp and a high impedance speaker is a small load.

To push more air, several speakers always of equal impedance can be wired together in a cabinet. The cabinet impedance depends on how the speakers are wired and may differ from the impedance of the speakers.

Learn how to properly wire speakers to a receiver or amplifier using spring clips or binding posts with bare, pin, spade, or banana plug connectors. Understand the Easy Ways to Hook up Most Any Kind of Subwoofer. Make Wiring Stereos a Breeze by Using Speaker Wire Connectors.

Efficient Amplifiers For amplifiers there is really only one choice: These ultra-efficient wonders are inexpensive but obscure. T-amps are available in a couple of different sizes, based on different amp chips: Most of the ones I can find are only sold direct from Chinese vendors through Ebay. This means they are cheap, but it will take 2 weeks to get it. Please post if you know of other sources for these amps.

I bought and tested several of the common amps I found on ebay. Note that there are many vendors on ebay all selling the same amps or copies of the same amps. The names of the amps get a bit confusing, its easier to go by the photos. How to find these on ebay. You will find tons of these amps. Stand alone amps amps with a plastic or metal case: Dayton DTA-1 from parts-express.

Connect Your Phone to Your Car Stereo On the Cheap

Jul 19, Advertisement – Continue Reading Below I love my new Ford Mustang coupe, but stock radio’s flat, bass-less sound and distortion at high volumes left the audio enthusiast in me wanting more. Sure, I could have opted for the dealer upgrade when I bought the vehicle, but I wanted to choose my own components instead of leaving the decision up to Ford. I wanted my dashboard to look like a console from the Starship Enterprise. I wanted to be enveloped in crystal clear sound with crisp highs and full mid-tones.

I wanted a rich, ground-trembling bass that shook the sidewalk as I cruised with the volume cranked. So, against the better judgment of the audio experts I consulted, I took up the challenge to install a sophisticated car audio system–complete with GPS navigation, a DVD player, an iPod connection and a Blue Tooth hands-free mobile phone kit, all controlled by a 7-inch touch screen–on my own.

If you want to run two speakers off each of your amp’s four channels, eight speakers total, then yes, you can do that using two 9-conductor cables connecting the amp to the vehicle harness. Just connect two speakers, left dash and door speakers, for example, to each amplifier output terminal.

Next If your subwoofer doesn’t have an internal amplifier , you’ll definitely want to connect an amplifier to it. To do this, you’ll need your subwoofer, an amplifier, at least one set of RCA cables these are the red, white, and yellow jacks on a single cable , speakers , and speaker wires. First, you’ll want to think about where you’ll keep the subwoofer.

Because the subwoofer is working mostly on the bass the low tones , it doesn’t require as much directional pushing as speakers do. Since you’ll have to run cables and wires between the subwoofer and other devices, you might want to keep it just a few feet from your screen. To get started with the actual hook-up, you’ll connect the subwoofer to the amplifier using the RCA cable.

If you want a stereo hook-up, you’ll need two sets of RCA cables.

Running a subwoofer with a stereo amp (no sub output)

How Hide TV Cables Audiophiles are always looking for new ways to get the most out of their audio equipment. Over the years people have found creative ways for enhancing sound quality beyond just buying more expensive speakers. There are two techniques in particular that we will talk about here: While neither of these techniques are strictly necessary, they can potentially give you better sound. Speakers are usually a combination of two specific speakers: Both Bi-Wiring and Bi-Amping try to improve sound quality by isolating these components from one another.

The amount of space you have to work with will help determine the size amp you buy. A common place to fit an amp is in the trunk or luggage compartment of your car.

Subwoofer Setup Part I: Placement and positioning While a subwoofer’s deep bass is nondirectional, it would be unwise to just stick the sub anywhere that’s convenient in your room. Corner placement is the de facto strategy for most people, possibly because the sub will then be out of the way and almost always produces the most bass, but corner placement may not yield the most accurate bass, or smoothest transition to the speakers. The sub and speakers have to work together as a team, and ideally you should never hear the sub as a separate sound source.

All of the bass should appear to come from the speakers. With small speakers, it’s best to keep the sub within 3 or 4 feet of the front left or right speakers. Once the sub is a lot farther away, it will be harder to maintain the illusion the bass is coming from the speakers. For really small speakers or skinny sound bars, keep the sub as close as possible to the speaker s. If you have larger speakers with 4-inch or larger woofers , some placement experimentation may be useful; play a CD with lots of deep bass and keep repeating the track as you move the sub to all of the visually acceptable locations in your listening room.

You’ll be amazed just how different the bass sounds in different locations — some will be muddy, some will sound louder, and some will reduce the bass volume. The goal is to get the best balance of deep bass from the sub and still have the mid and upper bass from the speakers in equal proportions adjust the subwoofer volume control in each new position. In some rooms, smooth bass response won’t be all that hard to achieve, but I’ve heard my share of “problem” rooms where the bass always sounds boomy or muddy.

If you’re having problems finding the perfect spot, try this method:

How to Connect a Subwoofer into Car Stereo Without an Amplifier

So what will we need to do this? But I doubt any of you guys will be using an amp that big. Walmart sells amplifier kits as do some other stores.

If the subwoofer features spring clips in order to use speaker wire, then you can use the speaker output of the receiver to hook it all up. This process is the same as connecting a basic stereo sure to mind the channels.

Most receivers have either preamp-in and preamp-out connections or tape monitor connections. In most cases, these are the best way to connect an equalizer to your stereo. Connecting to the tape monitor channels will require connection to only your receiver. Learn how to hook up an equalizer to the receiver instead. To run a signal from your stereo receiver to the equalizer and then to your amplifier, you will need 2 sets of RCA cable the same kind that is usually used to connect source components like turntables and CD players.

The length of the RCA cables should match the length of the distance between the receiver and the equalizer. Connect one pair of cables to the pre-amp output channels on the receiver and the other end of the cable to the left and right channel inputs on the equalizer. You will usually find these channels on the rear of the equalizer. Right channel jacks will usually take the red colored RCA plug while left channel should take white or black RCA plugs.

Can i hook a car amp up to my home stereo?

They have two separate speakers that emit different ranges of sounds. The woofer, or the larger speaker, emits the lower to mid range frequencies. The tweeter, the small speaker, covers the high range frequencies and noises. Separating the tweeter and woofer allows clearer sound with less distortion. Finding, researching and purchasing car speakers that fit the needs of your vehicle is difficult.

Mar 04,  · I made this because It was hard for me to figure out how to do. So I figured others would have trouble. Heres a video of me explaining how to hook up car speakers in your room to an amplifier.

In this article we look at some of the practical ways of wiring four speakers to each amplifier left and right. For example, it is normal to have your main HiFi amplifier in the lounge room. It is also common to want to have some speakers in the family room, outside patio or pool area and in the workshop or garage. If you need to connect just 2 pair of speakers to a HiFi stereo amplifier that is, 2 speakers to 1 amp , see my article on How to connect 2 speakers to 1 amplifier.

I have had many people over the years tell me it is easy to connect multiple speakers — all you have to do is wire the speakers in series. In the following diagrams I will only show the wiring for one side of a stereo amplifier, lets says the left side of the stereo. In reality this wiring needs to be duplicated for the right side speakers too.

How to Bi-Wire and Bi-Amp Your Speakers

This makes the GTO an ideal match to systems powered with head-unit or factory-amplifier power levels, or even with many of the GTO Series amplifier combinations to help keep up with systems that feature one or more subwoofers. And its great power-handling specifications also increase reliability over the lifetime of the speaker. With an effective increase in cone area, the speaker radiates more air.

Also, the carbon-injected cone material produces a lighter and stiffer cone. The result is a better low-frequency response and a greater ability to make those important musical notes that people often associate with larger speaker sizes. The result of this control is accurate sound in your car.

How do i hook up my amp and speakers T+ Which one set of bi-amplifying your computer is cheaper than the radio’s output of binding posts. If you turn an older receivers and how to your amp might be connected to play music.

Choosing speakers Choosing speakers Whether you are fitting four new speakers, or just adding an extra pair to your existing system, the choice is vast. Below are some old speakers and fader controls from Pioneer. A TS-VX is a surface-mounted wedge-type rear speaker. B TS-R mounts into the rear parcel shelf. C TS-X30 is a surface-mounted rear speaker. D TS flush-mounted speaker for use in front or rear locations.

How To Hook Up Car Audio Amplifier For Subs – Basic and Simple Guide


Comments are closed.

Hello! Do you want find a sex partner? Nothing is more simple! Click here, free registration!